LevelOne FCS-1010/WCS-2010 P/T IP Network Camera User Manual Ver 2.0.1 - 0609
4 Click on “Installation Wizard” after the window contains changed, click on “Installation Wizard” to run installation program. Upon
5 For the MAC address in the “MAC address” field, please check the label on the bottom of the camera. The IP addresses shown in the "C
6 Initial Access to the Network Camera Check Network Settings The Network Camera can be connected either before or immediately after software instal
7 How to Use Authentication After opening the Web browser and typing in the URL of the Network Camera, a dialogue window pops up to request a username
8 Installing Plug-in For the initial access to the Network Camera in Windows, the web browser may prompt for permission to install a new plug-in for t
9 Primary User’s Capabilities Main Screen with Camera View The main page layout has three parts: Configuration functions: The camera can be configur
10 The Configuration: “Digital Output” Clicking on the “On” or “Off” button turns the digital output to either on or off status. “Snapshot” The butto
11 “Disable digital zoom” The checkbox selection allows users to disable/enable the digital zoom function. “Zoom Factors” The range of zoom factor is
12 Client Settings At the initial access to the “Connection type” page in Windows, the web browser will ask for a new plug-in installation, the plug-i
13 allows HTTP Port (80) to be opened. In this mode, audio will not be sent and only video is operational. If no special need is required, UDP prot
14 Administrator’s Capabilities Fine-tuning for Best Performance There are a few choices the Administrator is allowed to maximize the capabilities of
15 shooting fast-moving images, you may want to slow the maximum frame rate down to 20 fps in order to lower the rate of data transmission. This allow
16 Opening Accounts for New Users Protect Network Camera by passwords Network Camera is shipped without any password by default. That means everyone c
17 Building a Multimedia Web Attraction Site Demo on Multiple Sites – Mid-Scale Service The Network Camera can allow ten visitors to view on-line simu
18 4. Click on “Application” in the left column, 5. Select the day or days of the week in “Weekly schedule” you want to upload the pictures, 6. Selec
19 bandwidth for best result. If the refresh rate is too fast and there is a large number of visitors, this may overload the Network Camera and slows
20 <html> <p align=left> <font size="7" face="Comic Sans MS" color="#FF0000"> Network Camera Demo
21 Building a Security Application The Administrator can combine options on the application page to perform many useful security applications. There a
22 Send Snapshots When Motion is Detected If no external sensor is available, the Administrator can use the built-in motion detection to monitor any
23 9. Click on “New” to have a new window to monitor video, 10. Type in a name to identify the new window, 11. Use the mouse to click, hold, and drag
3
24 Software Revision Upgrade Customers can obtain the up-to-date software from the web site of LevelOne,www.level1.com. An easy-to-use Upgrade Wizard
25 Multi-Language by Software Upgrade The software in FCS-1010/WCS-2010 Network Camera is four language, English, German, Korean and Chinese. The defa
26 2. Select the Camera you want to setup and click “Link to selected device” button. 3. Please Enter “root” as username and MAC number as password.
27 4. After log-on to the camera, please click “Configuration” button. 5. Select “Network” linkage in left frame. Once entering to the network page,
28 6. Launch the Upgrade Wizard from your CDROM 7. Type the Camera’ s IP address & root’s password which you have to upgrade its firmware. Then,
29 the Video Server and pop-up the message dialog to ask. If the firmware version is correct, click “Yes” button. 10. Then, the firmware will start
30 and password, the main page should display. Click the “Configuration” linkage
31 Definitions in Configuration Only the Administrator can access system configuration. Each category in the left column will be explained in the foll
32 System Parameters "Host name" The text displays the title at the top of the main page. “Turn off the LED indicator” Check this option t
33 User Group Administration “Root password” Change the Administrator’s password by typing in the new password identically in both text boxes. The typ
4 Package Contents
34 Network Settings Any changes made on this page will restart the system in order to validate the changes. Make sure every field is entered correctly
35 Streaming “Control channel port” This can be something other than the default port 5001 in order to work with the port opened by the firewall. “A
36 “Data encryption” Checking the box to enable the data encryption. By default it is disabled. “Auth. Mode” Choosing one of the following modes, (Ope
37 “Return email address” The return email address used in the event the mails fail to be sent out. FTP “Local FTP server port” This can be other than
38 Audio/Video Codec Parameters Audio Parameters “Mute” Check the option will make the Network Camera reboot to force all the connection using HTTP mo
39 “Contrast”, “Hue” and "Saturation" for video compensation. Each field has eleven levels ranging from -5 to +5. The User may press to f
40 Motion Detection “Enable motion detection” Check this option to turn on motion detection. Click on this button to add a new window. At most thr
41 Application Setup Weekly Schedule “Sun” ~ “Sat” Select the days of the week to perform the following operations. “Snapshots begin at” Set the time
42 Sequential Operation “Snapshot every second(s)” The Network Camera will send snapshots at the specified intervals to the external server using the
43 Camera Control On the Camera Control page, there are two main function control areas: Camera Control Area The pan and tilt functions can be contro
5 Table of Contents INSTALLATION ...
44 Preset Function Area ”Enable IR control” Checking this box allows the Administrator to enable the IR controller to move the aim of the camera.
45 UPnP and DDNS Settings “Enable DDNS” This option turns on the DDNS function. “Provider” The provider list contains four hosts that provide DDNS ser
46 Viewing System Log Click on the link on the configuration page to view the system log file. The content of this file provides useful information ab
47 Appendix A. Troubleshooting Status LED After powering up, the Network Camera performs a self-diagnostic to detect any hardware defects. The followi
49 B. Frequently Asked Questions Q What if I forget my password? A After the Administrator's password has been assigned, every access to the Net
50 Q The image is not clear enough. A Rotate the lens to adjust the focus after the Network Camera has been installed in the proper position. The ima
51 In general, the transfer rate in a general local network environment can achieve over 200 kilobytes per second and approximately 10 to 20 pictures
52 C. URL Commands of the Network Camera For some customers who already have their own web site or web control application, the Network Camera can be
53 Restart System /setup/reset.cgi Restart the Network Camera without warning.
54 Page URL The configuration page has a frame layout including an option list frame and an option page frame. Referenced URLs, except for the config
6 Motion Detection ...
55 <general format> URL[?[name=value][&name=value]……] <method> POST <authorized user> root System Configuration URL URL: /setup
56 Security Configuration URL URL: /setup/security.cgi NAME VALUE DESCRIPTION rootpass <text string shorter than 15 characters> change root p
57 no keep the original way ssid <text string shorter than 33 characters> WLAN SSID inf WLAN infrastructure mode wl ad WLAN Ad Hoc mode 1 ~ 1
58 netkey2 hexadecimal string (00 ~ FF) network key 2 netkey3 hexadecimal string (00 ~ FF) network key 3 netkey4 hexadecimal string (00 ~ FF) n
59 smtp2 <domain name or IP address> secondary SMTP server mailto2 <text string shorter than 80 characters> mail recipient address mai
60 B/W monochrome color <other than B/W> color fixb fix bit rate quality <other than fixb> fix quantization 1 lowest quality of video
61 internal set the audio source from built-in microphone. mphone external set the audio source from line-in microphone. Camera Control URL URL:
62 Application Configuration URL URL: /setup/app.cgi NAME VALUE DESCRIPTION emode <not required> event mode application smode <not require
1 Installation Hardware Installation Please verify that your product package contains all the accessories listed in the foregoing Package Contents.
2 The Network Camera provides a general I/O terminal block with one digital input and one relay switch for device control. Pin 1 and Pin 2 can be con
3 Software Installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refers to t
Commentaires sur ces manuels